Easy DIY Stand Mixer Tray with Attachment Organizer

by

Kati

Turn scraps into a tray to organize your mixer attachments.

I love my stand mixer, but hate that the paddles and attachments take up too much space in my drawers. And the whisk barely fits anyway.

So since I already dedicate counter space to my stand mixer, why not make it beautiful and add some storage for all those attachments.

This simple to build tray is the perfect home for your mixer, while organizing up to 5 different attachments. And it would make a great DIY gift for the baker in your life.

This post may contain affiliate links. As an Amazon Associate I earn from qualifying purchases. Click here to read my full disclosure policy.

Stand mixer on a wood tray with attachments stored on the back.

Mixer Storage Ideas

This simple project may just become your new favorite storage.

Without taking much more space than a stand mixer already does, you can add room to organize the paddles, whisks and kneaders.

They stand easily on dowels in the tray to always be ready and no longer get all tangled up in a drawer.

Wood tray with dowels to hold Kitchenaid mixer paddles and whisks.

How to Build a Stand Mixer Tray

Tools & Materials

Recommended Tools:

Supplies:

  • Wood products
    • 1x boards
    • 7/16″ dowel
  • Wood glue
  • Silicone or felt feet

STEP 1- Create a template

I placed my stand mixer on a piece of butcher paper.

I wanted the tray 3/4″ wider than my base, so I used a 3/4″ thick scrap of wood as a spacer while I traced around it.

Tracing the base of a stand mixer with attachments to make template.

Then I put all the attachments behind it and traced around their bases.

I drew an curve around the back to enclose all the attachment bases then cut out my template.

EXPERT TIP:
To make sure my tray is symmetrical, I folded it in half and trimmed the back section as need so they matched.

Drawing a curve around the attachments on the back of the template.

STEP 2- Cut the tray

Now that I knew how big my board needed to be. I found some 1x scraps, mine was hickory left over from building this X-leg bench.

I cut the scraps to the length I needed (plus a couple inches for wiggle room).

Then to make the scraps the width that I needed, I glued them together at the edge to make one large board.

Glueing two hickory boards together to create a wider board.

After the glue dried, I sanded everything. Then I traced my template on the board.

I cut the tray shape out with a jig saw. Then sanded the edges nice and smooth.

Tracing the template and cutting it out with a jig saw.

Finally, I double checked the placement of all my attachments to make sure I still liked where they were on the template.

Then I marked the center point of each of the bases. And drilled a 7/16″ hole 1/2″ deep at each point.

Drilling holes at the center point of the attachment bases.

To soften the top edge, I added a round-over with my trim router. You could also do this with a sander.

Routing a roundover on the top of the tray.

STEP 3- Add dowels to hold attachments

Cut the dowels to fit inside your attachment + 1/2″ to fit into the hole. Mine were 1 5/8″ long.

Then add glue inside the holes and tap the dowels all the way to the bottom.

Using a hammer to tap dowels into the holes.

STEP 4- Finish

Sand anything that needs it. Then stain/seal your tray.

This would also be a fun project to add a faux laser engraving to. The large flat surface is the perfect spot for personalizing.

Sealing the stand mixer tray with a tung oil sealer.

If you are worried about the wood scratching the countertop, add silicone or felt feet to the bottom.

But make sure the finish on the wood is completely dry or they will not stick well.

Adding silicone feet to the bottom of the wood tray.

And it’s all done!

Now I have the perfect home for my stand mixer and it holds all my paddles and attachments. I love how organized they are.

Wood tray with a stand mixer on top and storage on the back organizing all the attachments.

DIY Gift Week- Day 3

We are already half way through gift! Everyday this week I am sharing a new DIY gift idea along with my friends from WoodShop Diaries and Anika’s DIY Life.

Today’s DIY gift ideas are all perfect for entertaining and baking! Then don’t forget to come back and see tomorrow’s gifts too.

Happy building!

-Kati with picture of blog author Kati

Would you like to save this tutorial?

I'll email this post to you, so you can come back to it later!